2012年5月9日水曜日

さくらのクラウド ディスクの追加 on CentOS5

※this text from livedoor blog 2011/11/16

さくらのクラウドのコントロールパネルでディスクを追加・接続した後に ディスクをマウントして使えるようにします

ディスクのパーティションを確認

# /sbin/fdisk -l

Disk /dev/hda: 21.4 GB, 21474836480 bytes
255 heads, 63 sectors/track, 2610 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/hda1   *           1          13      104391   83  Linux
/dev/hda2              14        2355    18812115   83  Linux
/dev/hda3            2356        2610     2048287+  82  Linux swap / Solaris

Disk /dev/hdb: 107.3 GB, 107374182400 bytes
255 heads, 63 sectors/track, 13054 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/hdb1               1       13054   104856223+  83  Linux
ディスク/dev/hdb1が追加された事がわかる

ディスクのパーティションを設定

# /sbin/fdisk /dev/hdb1
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.


The number of cylinders for this disk is set to 13053.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)

Command (m for help): p

Disk /dev/hdb1: 107.3 GB, 107372772864 bytes
255 heads, 63 sectors/track, 13053 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

     Device Boot      Start         End      Blocks   Id  System

Command (m for help): n
Command action
   e   extended
   p   primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-13053, default 1): 
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-13053, default 13053): 
Using default value 13053

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: Re-reading the partition table failed with error 22: Invalid argument.
The kernel still uses the old table.
The new table will be used at the next reboot.
Syncing disks.


ext3 形式でファイルシステムを構築

# /sbin/mkfs -t ext3 /dev/hdb1
mke2fs 1.39 (29-May-2006)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
13107200 inodes, 26214055 blocks
1310702 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=4294967296
800 block groups
32768 blocks per group, 32768 fragments per group
16384 inodes per group
Superblock backups stored on blocks: 
        32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 
        4096000, 7962624, 11239424, 20480000, 23887872

Writing inode tables: done                            
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 23 mounts or
180 days, whichever comes first.  Use tune2fs -c or -i to override.


マウントポイントの作成とマウント

# mkdir /hdb1
# mount /dev/hdb1 /hdb1
# df -h
Filesystem            Size  Used Avail Use% Mounted on
/dev/hda2              18G  1.5G   16G   9% /
/dev/hda1              99M   17M   77M  18% /boot
tmpfs                 1.8G     0  1.8G   0% /dev/shm
/dev/hdb1              99G  188M   94G   1% /hdb1
これで、追加したディスクが/hdb1で使えるようになりました

起動時に自動マウントするようにしておく

# emacs /etc/fstab
/dev/hdb1               /hdb1                   ext3    defaults        1 2